Micropolis hard Disk Drives, Specifications, Support, Specs, Jumpers, Manual, Images

Micropolis 1325

Hard Disk Drive

Overview

Model Capacity Size Height Interface Bus Type
Micropolis 1325 69MB 5.25" FHT ST506 MFM

Video

micropolis 1325 picture micropolis 1325 picture
micropolis 1325 picture

Specifications

Size 5-1/4 Inch
Interface ST-506/412
Interface Type 
Encoding Method MFM (Modified Frequency Modulation)
Formatted Capacity 71.3 MB
Disks 5
Heads 8 (9 with alignment head)
Cylinders 1024
Sectors 17
Buffer Size N/A
Average Seek 28 ms
Single Track 6 ms
Rotation Speed/Avg. Latency 3600 rpm +/- 0.5%
Transfer Rate to / from. media 5 Mbits/sec
Transfer Rate to / from buffer N/A
Tracks Per Inch (TPI)
Bits Per Inch (BPI)
Dimensions 8.0"L x 5.75"W x 3.25"H
Weight 5.75 lbs.

Power Requirements

+12V +/-5% +5V +/-5% Power
Spin up 3.9A (max)
Read / Write 2.0A avg 0.9A avg
Typical 32 Watts

Notes

These drives actually have 9 heads, where 8 read/write heads are used for user data and the topmost head, head 9, is used for servo tracking data.

Drive Addressing and Interface Termination

Note that due to how the jumpers are located on the PCB and how the PCB is mounted inside the drive's metal chassis, jumpers are hard to reach. That's why the PCB is mounted in a way that it can be swung out. Place the drive on your workbench vertically with the PCB facing you. Then loosen the two screws located on the top. The PCB is mounted with hinges on the bottom and can then be poped down for inspection and easier access to the jumpers and motor assembly.


DS1, DS2, DS3, DS4 Drive Select Jumpers
  The Drive Select jumper locations are identified as DS1, DS2, DS3, and DS4. Only one Drive Select jumper is installed on a drive. The drives are shipped with the jumper installed at DS1. For every drive in a PC/AT installation, move the jumper from DS1 to DS2 (the special twisted interface cable that is generally used takes care of assigning a unique address to each drive). Some other systems may require that each drive be jumpered to a unique address (i.e., different DS numbers).

RN1 Interface Terminator
  The Interface Terminator factory installed at RN1 provides proper termination for the interface lines. When daisy-chaining multiple 1325 drives, leave the terminator in the last physical drive on the daisy chain cable; remove the terminator from each of the other drives. In most PC/AT installations, the C: drive is actually at the end of the cable and should retain the terminator.

W1 Write Fault Latch
  W1 is the Write Fault Latch. If W1 is present and the drive encounters a write fault, all writing to the drive is inhibited until after the drive has been de-selected. If W1 is absent, fault conditions are not latched. Drives are shipped with a jumper installed at W1; remove it for PC/AT installations.

W2 is always installed.

W7 is never installed.

W8 is always installed.

OEM naming variants and jumper settings

Digital Equipment Corporation (DEC) used the Micropolis 1325 drives white-labeled as the DEC RD53 hard-disk drives for their PDP11/10 VAX machines. To make a non-DEC Micropolis drive work with a DEC system, jumper R7.
DEC RD53-A and RD53-EA with skid plate.
DEC RD54 was a Maxtor drive.

Interface

The drive uses the de-facto industry standard for MFM disk drives, the ST412 interface, which was adopted by numerous HDD manufacturers of the time and was widely used well into the 1990s. With its origin in floppy drive interfaces, this hard disk interface standard goes back to the Shugart Associates SA1000's interface, an 8-inch hard drive. The successor hard disk drive, Shugart Associates ST506, was the first 5.25 inch hard disk drive. It stored up to 5 MB after formatting (in 153 cylinders, using 4 heads, 26 sectors/track, 256 bytes/sector). This device was followed later in 1981 by the similar ST412 HDD which made 10 MB of on-line storage available by doubling effective cylinders to 306. At that point, the ST412 interface semantics had settled.
Platters and r/w-heads of an openened hard-disk-drive
Opened Micropolis 1325 hard-disk-drive, showing data surfaces (platters) and r/w-heads
Illustration from the Micropolis Data Storage Guide

External resources

- Article on fixing stuck heads
- Article on recovering data despite head centering issues
- Adjusting head/servo mechanism on a 1375
- Printable head fine adjustment tool